Back to Top
previous next


Bondexpo from 07.10 - 10.10.2019


We will exhibit at Bondexpo in Stuttgart this year. 
Venue: Messe Stuttgart  

Hall 6, Booth No. 6433

Productronica/Semicon 12.11. - 15.11.2019 in Munich

Visit us at Productronica and Semicon in Munich
we are looking forward to meet you!
Productronica:  Hall: A4/Booth: 301
Semicon:          Hall: B1/Booth: 750



Some Like it HOT, most do not...

The Latest Advancements in Adhesives for Thermal Management

Join us for a webinar on Tuesday, June 11, 2019

Register Now

We are celebrating the 30th anniversary of John P Kummer Ltd.
JPK Ltd. was founded on Monday 15th May 1989.

The “dam & fill” process with two materials is mainly used in cases where a component needs to be protected with an optically-transparent encapsulant or if a conventional glob-top material is too viscous to flow around and underneath fine wires. Optically transparent encapsulants usually have a low viscosity. A dam is therefore applied around the component first to prevent the potting material from flowing all over the substrate.

Epo-Tek OG116-31 is a UV-curable epoxy. Due to its thixotropic nature it is often used as a dam. It can be cured with UV-light in a very short time. Afterwards the encapsulant – either also a UV-cure or a thermoset material - can be applied. 

Epo-Tek OG198-55 has an even higher thixotropy than OG116-31.

Both products have an extraordinary chemical and humidity resistance and a high glass transition temperature (Tg >110°C).

As most UV-cure epoxies, both OG116-31 and OG198-55 are cationic products. Ionic polymerization is initiated by photo-generated ions. The cure process continues until all polymers are consumed. Generally, cationic products have the benefits of less shrinkage and higher adhesion over free radical cured systems and are not adversely impacted by an oxygen rich curing environment.

Location:                               France (Grenoble region)
Starting date:                        With immediate effect       
Mandatory requirement:       Willingness to travel at least 50% of working time within France and Europe


Find more information here Carrière


John P. Kummer Group is proud to announce its partnership with Micromanipulator, manufacturer of probing systems and accessories.

Find more information here

The VCA Optima series contact angle measurement systems incorporates lightweight design, easy assembly, and the latest Windows™ standards and user-friendly software. VCA-optima systems are suitable for research or quality control in R&D and process engineering. Systems range from the basic Optima to the fully equipped Optima XE. Features include dynamic capture capability, motorized syringe, surface energy analysis and pendant drop analysis, to name a few.


The pre-recording of the webinar is now available for those who were not able to listen in.  You can register by clicking on the below link and view the presentation at your leisure.

We are expanding our dispensing product line with two of the world’s leading specialists in the field:

NSW Automation from Malaysia and TAEHA Corporation from Korea.

Both companies are experts in their specific fields and offer remarkable solutions to dispensing requirements for the micro- and optoelectronics, automotive, LED, medical, and semiconductor markets

Epoxy Technology Europe Ltd has doubled the size of its production site in the UK in order to keep up with ever-increasing demand for packaged EPO-TEK® adhesives. The quality control area, controlled light area, as well as freezer and general storage capacity were also augmented.

Why should a customer choose to outsource the syringe-making-process? There are several important reasons to do so, all result in cost savings for the customer in the end. Here a brief summary of the major factors:


  • Reduced waste material - match fill amounts to match production requirements
  • No need for the customer to buy consumables etc. All syringes are labelled per GHS requirements
  • No need for material transfer tools


  • No space required for syringe-filling, no fume cupboards etc. for mixing
  • Higher safety for employees - less exposure to wet chemicals
  • No specialized mixing equipment required
  • Reduced labor costs 
  • No special employee training required for mixing processes
  • Full certification and traceability

Process Development/Production and Test Equipment/Quality Control:

Material characteristics can be considerably influenced by the mixing process, as well as steps such as degassing and centrifuging. One illustration of the potential for this change is how viscosities can change; for a silver-filled material the VR values can be affected and thixotropy could be destroyed if a proper process development is not set-up for each product. For reproducible quality of packaged material, exact time parameters need to be established for each product as epoxy materials change in characteristics with time once mixed. Only if the customer decides to outsource this process to the manufacturer can he be assured that the packaged material has consistent performance.

Epoxy Technology Europe Ltd offers various processing options, including vacuum degassing. All syringes are centrifuged to remove bubbles. From the customer’s point of view all other aspects of processing are avoided (process documentation, scales, mixing tools, dispensers for transfer of material to end syringe, centrifuge, etc.) and importantly there is no requirement to set up a QC process to document the quality of the mixed material and equipment to perform QC tests on mixed material. A full range of Quality Control tests are provided by Epoxy Technology Europe and include Viscometry, Cure Calorimetry, Cure testing, etc.

At Epoxy Technology, full traceability is given back to each raw material. For each product, a process is in place for to record all parameters such as time from mixing to freezing, mix quantities, degassing and centrifuging parameters, and more. This ensures that the customer receives material of the same consistent quality and can maintain a reproducible process on his end. For each order the customer receives a C of C for his documentation which provides traceability at the ‘Mix-Lot’ level.

Standard syringe sizes are 3, 5, 10, 30 and 55 cc. The syringes are compatible with standard dispensers. Special syringes are available upon request. Fill quantities depend on the customer’s consumption. All European EPO-TEK®-customers who order the material premixed frozen are supplied from Epoxy Technology Europe’s European facility. Transit time is usually 24 hours, shipments are made in dry ice and temperature profiles can be logged.

Highly demanding industries such as: medical, automotive, aerospace and others have been supplied since 2010 with EPO-TEK® products packaged in the UK.

We are happy to announce the business relationship with our new principle Optotherm Inc.

The John P. Kummer Group will promote the system “Sentris” for semiconductor failure analysis on the European market. The Thermal Imaging Microscope pinpoints the low-level infrared thermal emissions by IC faults such as short circuits and leakage current.

Please contact us, we are at your disposal.

More information:

Our website uses cookies. By continuing we assume your permission to deploy cookies, as detailed in our privacy policy.